Technology Capabilities

Your Direct PCB & PCBA Manufacturing Partner

PCB Capabilities
Home PCB Capabilities

PCB Manufacturing Capabilities & Design Parameter Specifications

I structured our PCB manufacturing capabilities around the exact design rules hardware engineers check during layout—minimum trace and space for 1 oz or 2 oz copper, laser microvia diameter for HDI boards, controlled impedance tolerance for high-speed signals, and thermal limits for metal-core PCBs—so you can validate manufacturability and open the matching board spec page in a new tab.

Upload Gerbers for DFM & Quote
PCB fabrication parameter diagram covering trace and space, controlled impedance, laser microvias, backdrills, thermal limits, and surface finishes
Core PCB fabrication parameters mapped across copper routing, impedance, vias, and finishes.

PCB Capability Matrix by Design Parameter

Filter by board type, process category, or long-tail design keywords. Every row shows Standard vs. Advanced limits, explains the practical design check, and links to the relevant board specification page in a new window.

Process Category Design Parameter, Long-Tail Fit & Board Links Standard Advanced
Etching & Trace
Minimum Trace & Space (1 oz Copper)
Minimum trace width and spacing for 1 oz outer/inner routing without etching undercut.
4 mil / 4 mil (0.10 mm) 3 mil / 3 mil (0.075 mm)
Microvias
Laser Microvia Diameter & Capture Pad
Laser-drilled blind/buried microvia sizing for fine-pitch BGA fan-out and HDI build-up.
0.10 mm (4 mil) 0.075 mm (3 mil)
Impedance Control
Controlled Impedance Tolerance & Backdrilling
Single-ended and differential impedance accuracy for high-speed serial lanes and RF lines.
±10% (≥50 Ω) / ±5 Ω (<50 Ω) ±5% – ±7% (Backdrilling available)
Thermal & Copper
Thermal Conductivity & Heavy Copper Weight
Heat dissipation W/m·K and heavy copper thickness for LED drivers and power modules.
1.0 – 2.0 W/m·K (1–3 oz) 3.0 – 8.0 W/m·K (4–6 oz heavy copper)

Verification Standards & Board-Specific Guides

I back up our parameter limits with optical, electrical, and impedance verification, and point each design scenario to a dedicated board page that opens in a new tab.

Quality control workflow showing AOI inspection, TDR controlled impedance coupon testing, and electrical continuity verification
AOI, TDR impedance coupons, and electrical testing used to verify production tolerances.
Board family selection guide connecting multilayer FR-4, HDI, high-speed laminates, and metal-core boards to design rules
Mapping board families to stack-up symmetry, microvia structure, thermal paths, and finishes.

Stack-Up & Impedance

When you target controlled differential impedance, I advise checking prepreg glass weave and dielectric thickness before locking net rules.

Stack-up & impedance guide

Surface Finish Selection

I usually recommend ENIG for fine-pitch BGA coplanarity, while OSP or lead-free HASL suits cost-focused builds with standard pitch parts.

ENIG vs. OSP & HASL comparison

Pre-Release DFM Check

Checking narrow solder mask dams, hole-to-copper spacing, and via-in-pad expectations early prevents avoidable CAM holds.

Pre-release DFM checklist

Frequently Asked Questions on PCB Capabilities

How do Standard and Advanced capabilities differ in lead time and unit cost?
Our Standard tier covers high-yield, mainstream fabrication windows with faster turnaround and lower cost. Our Advanced tier covers tighter trace/space rules, laser microvias, backdrilling, and specialty laminates that require tighter process control and often benefit from a DFM check before release.
What if my design needs tighter tolerances or heavy copper beyond the Advanced column?
The table reflects our standard production and advanced windows. If your board needs custom stack-ups, extreme aspect ratios, or specialized tolerances, our CAM engineers can review feasibility and run a custom engineering check.
Which files should I send to verify my PCB design and get a quote?
Please share RS-274X Gerber files, an Excellon drill file, your stack-up details, and any controlled-impedance or surface finish requirements so we can verify manufacturability accurately.
Send Message
Name*
Email*
Company Name*
Address
Job Title
Phone Number