PCB Surface Finishes

Your Direct PCB & PCBA Manufacturing Partner

PCB Surface Finishes
Home PCB Surface Finishes
PCB Surface Finishes: ENIG, HASL & OSP Comparison | GemTech PCB

Surface Finishes for Your Assembly Requirements

A PCB surface finish is the coating applied to exposed copper on a printed circuit board. It protects the copper from oxidation and keeps the surface solderable for component assembly. Common PCB surface finishes include ENIG, HASL and OSP, each suited to different design, assembly and storage requirements.

Our standard options include these three finishes, applied under controlled process conditions for prototype and low-volume production. Compare them below — including ENIG vs HASL — or contact our team to confirm the right finish for your project.

ENIG Macro Same-magnification pad view
HASL Macro Same-magnification pad view
OSP Macro Same-magnification pad view
Line Detail Finishing line detail photo

PCB Surface Finish Types

[ INSERT PHOTO S01 ] ENIG flat gold pad macro

01 ENIG (Electroless Nickel Immersion Gold)

ENIG deposits an electroless nickel layer over the copper, followed by a thin immersion gold layer that helps protect the nickel from oxidation during storage. It gives a flat, uniform surface for fine-pitch BGA and QFN components.

Considerations: higher cost than HASL or OSP; the nickel layer can add conductor loss in high-frequency designs.

[ INSERT PHOTO S02 ] HASL bright solder pad macro

02 HASL (Hot Air Solder Leveling)

HASL coats the copper with molten solder and levels it with hot air knives. It is a low-cost, robust finish with good solderability, well suited to through-hole and general SMT assembly; rework is straightforward.

Considerations: less flat than ENIG or OSP, so fine-pitch paste printing needs evaluation; the laminate is exposed to the elevated temperatures of molten-solder application. Lead-free HASL variants are available; the alloy for an order is confirmed during engineering review.

[ INSERT PHOTO S03 ] OSP copper-tone pad macro

03 OSP (Organic Solderability Preservative)

OSP applies a thin organic film over the copper to preserve solderability until assembly; flux removes it during soldering. It is typically one of the lowest-cost finishes and leaves the surface flat for fine-pitch SMT.

Considerations: sensitive to handling, heat and humidity; shelf life and reflow tolerance depend on the chemistry and thermal profile. Certain qualified high-temperature OSP formulations are designed for lead-free assembly; compatibility depends on the selected chemistry and assembly profile.

Beyond these three standard finishes, our capabilities also include ENEPIG, immersion silver, immersion tin, electrolytic hard and soft gold, selective ENIG+OSP, and carbon ink. Availability depends on board type; contact our team to confirm the options for your design.

Explore ENEPIG, Hard Gold & Selective Finishes →

[ INSERT PHOTO S04 ] Optional: Selective ENIG+OSP / Gold Finger

PCB Surface Finish Comparison

The table compares the three standard finishes. Values are general characteristics; order-specific limits are confirmed during engineering review.

Attribute ENIG HASL OSP
Coating Electroless nickel + immersion gold Solder, hot-air leveled Organic film over copper
Surface flatness Excellent Moderate; solder meniscus on pads Excellent; follows the copper profile
Fine-pitch BGA / QFN Suitable Pitch-dependent; evaluate paste printing Suitable
Solderability shelf life (industry reference) Approximately 12 months Approximately 12 months Approximately 6 months
Reflow tolerance Multiple cycles (profile-dependent) Multiple cycles (profile-dependent) Chemistry- and profile-dependent; qualified high-temperature systems support multiple excursions
Lead content of finish material No lead-based solder alloy Alloy-dependent; confirm per order No lead-based solder alloy
Relative cost (qualitative) Higher Low Typically lowest
Best for Fine-pitch SMT, BGA/QFN, lead-free assembly Through-hole, general SMT, cost-driven builds Fine-pitch SMT, short-cycle consumer boards
Need help matching pad pitch, reflow cycles, and finish cost? Share your Gerber and stack-up for engineering review. Check Finish Compatibility

ENIG vs HASL: Which Should You Choose?

Choose ENIG when your design requires a flat surface for fine-pitch BGA or QFN components. Choose HASL for through-hole and general SMT boards where cost is a priority and pad pitch is compatible with the process. ENIG offers better surface flatness, while HASL is less expensive and easier to rework. As a quick guide, ENIG suits fine-pitch assemblies, HASL is a cost-effective option for general SMT and through-hole boards, and OSP suits flat, low-cost builds with controlled storage and assembly conditions.

Review Fine-Pitch BGA & PCB Fabrication Capabilities →

Shelf life figures are industry references, not guarantees; actual values depend on the finish formulation, packaging, storage conditions and acceptance criteria. OSP follows the underlying copper profile rather than leveling it.

[ INSERT DIAGRAM S05 ] Optional: Pad flatness cross-section diagram

PCB Surface Finish FAQ

What does OSP mean in PCB?

OSP stands for Organic Solderability Preservative — a thin organic film that protects the copper surface until soldering. It is low-cost and flat, but sensitive to handling, heat and humidity, so it suits short storage cycles and controlled assembly.

What is ENIG black pad?

Black pad is excessive nickel corrosion during the immersion gold step, which can cause brittle solder joints. It is controlled through bath chemistry and process management, and assessed by cross-section analysis and joint reliability testing when required — not by visual inspection or XRF.

Is HASL lead-free and RoHS compliant?

Yes — lead-free HASL variants are available, confirmed for our multilayer, high-layer-count and HDI boards. The alloy for an order is confirmed during engineering review. A lead-free finish material alone does not make the whole board RoHS compliant — compliance depends on all materials and applicable exemptions.

How long does ENIG last before assembly?

Common industry and supplier references often specify approximately 12 months for ENIG and HASL, and approximately 6 months for OSP. Actual solderability shelf life depends on the manufacturer's specification, packaging and storage conditions; the guaranteed period for an order is confirmed before production.

A Finish That Fits Your Assembly

Our team reviews surface finish requirements alongside your board design, assembly process and storage plan. Additional finishes — including ENEPIG, immersion silver, immersion tin, electrolytic hard and soft gold, selective ENIG+OSP and carbon ink — are available depending on board type. Surface finishing is one step in our controlled production flow — see our PCB Manufacturing Equipment & Quality Inspection page for how finishes are applied and verified.

Have a PCB project in mind? Contact our team to discuss your requirements.

Get Expert Support

Our team will get back to you within 24 hours


DFM & Design Review

Technical Consultation

Fast Response

How can we help you?
Name*
Email*
Company Name*
Address
Job Title
Phone Number
Message
Upload Gerber/PCB File:
Send Message
Name*
Email*
Company Name*
Address
Job Title
Phone Number